Apple Music Hear your music the way it was mastered. Get up to 3 months of Apple Music free, with lossless audio and Dolby Atmos. Try it free Ad · New subscribers only
SoundBench فارسی
Guides

What Is LUFS? Loudness Normalization Explained

LUFS is the unit streaming services use to judge how loud a track feels. Learn what it measures, why your song gets turned down, and what you can do about it.

If you have ever noticed that a loud song suddenly gets quieter on a streaming app, you have heard loudness normalization at work. The service measured the track, decided it was louder than its target, and lowered the playback volume so that every song feels about equally loud.

The measurement behind it is called LUFS. It is easy to confuse with the peak level you see on a volume meter, but the two numbers describe different things. This guide explains both, lists common targets, and shows how to check and change your own files in the browser.

What LUFS actually measures

LUFS stands for Loudness Units relative to Full Scale. Instead of looking only at the single highest spike, it estimates how loud audio feels to a person over time. It uses a weighting that gives less importance to very low bass and more to the mid and high frequencies the ear is most sensitive to, as defined in the ITU-R BS.1770 standard.

One loudness unit equals one decibel, so a track at -12 LUFS is 2 dB louder than one at -14 LUFS. Values are negative because they are measured down from digital full scale, and a number closer to zero means louder. The figure usually quoted for a whole song is called integrated loudness, an average across the entire file.

LUFS versus peak level

Peak level, shown in dBFS, tells you how close the loudest instant is to the digital ceiling. 0 dBFS is the maximum, and anything above it is clipped. Peak level says nothing about how loud a song sounds on average: a quiet acoustic recording and a heavily compressed pop track can share the same peak yet differ by many LUFS.

That is why loudness normalization uses LUFS and not peaks. Two tracks with identical peaks can still feel very different, and the integrated figure is what matches what listeners notice.

MeasureUnitWhat it tells you
Peak leveldBFSHow close the loudest instant is to clipping
Integrated loudnessLUFSHow loud the whole track feels on average
Crest factordBGap between peaks and average level; low means heavily compressed

Common loudness targets

Each platform picks its own reference level, and these can change, so check the current documentation before mastering for a specific service. The figures below are the commonly cited defaults.

Platform or standardTypical target
Spotify (default listening setting)about -14 LUFS
Apple Music (Sound Check)about -16 LUFS
EBU R128 (European broadcast)-23 LUFS

What happens when your track is too loud or too quiet

If a track is louder than the target, the service turns it down, so squeezing out extra loudness in mastering gains you nothing and often costs dynamics and punch. If it is quieter than the target, some services leave it alone and others raise it, depending on their rules.

The practical lesson is to master for good sound, not maximum volume. A track with healthy dynamics at a moderate LUFS often sounds as loud as an over-compressed one once both are normalized.

How to check and adjust your audio with SoundBench

SoundBench can measure integrated loudness in LUFS and raise or lower level in decibels, all inside your browser without uploading the file.

  • Open the SoundBench Audio Quality Analyzer at soundbench.net/fake-lossless-checker/ and add your track. Besides the quality verdict, it reports integrated loudness in LUFS, sample peak in dBFS and crest factor.
  • Compare the LUFS value with your target. For example, a result of -9 LUFS is about 5 dB louder than a -14 LUFS target.
  • Open the SoundBench Change Volume tool at soundbench.net/change-volume/ and add the file. Its current peak level is shown.
  • Use the gain slider or the plus and minus 3 and 6 dB buttons to set a precise change. Normalize sets the loudest peak to a target such as -1 dBFS, and Prevent clipping caps the boost automatically.
  • Switch between ORIGINAL and EDITED while playing to compare, then choose a format and click Export.

A note on peak normalization

The Normalize button in Change Volume works on the peak level, not on LUFS. It makes a file as loud as possible without clipping, which is useful for quiet voice memos and recordings, but it will not hit a specific LUFS target by itself. To aim for a LUFS value, measure first, then apply the gain change in decibels that closes the gap while keeping peaks under 0 dBFS.

Frequently asked questions

Is a lower LUFS number quieter?

Yes. LUFS values are negative, so -20 LUFS is quieter than -14 LUFS. The closer the number is to zero, the louder the track.

Does normalization reduce audio quality?

Turning playback volume down does not harm quality. Raising level on your own file can cause clipping if the peaks go past 0 dBFS, so keep an eye on the peak value.

What LUFS should my podcast or song be?

It depends on where it will be published. Many streaming services aim near -14 LUFS, while broadcast in Europe uses -23 LUFS. Check the current guidelines of your platform.

Related tools